With the exploration and innovation of company people, gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel.
1, Yield Strength. A yield strength or yield point is the material property defined as the stress at which a material begins to deform plastically. Prior to the yield point the material will deform elastically and will return to its original shape when the applied stress is removed, Yield strength of Q345B is 345 MegaPascals.
Q345 steel specification: Q345 steel belongs to 16Mn steel grade, usually it is produced in hot rolled state, hot rolled steel plate, hot rolled steel coil/sheet, it has comprehensive mechanical and welding property, as it shows good performance in structural purposes, it is widely used as welding structural part in manufacturing of ship q345b yield
Q345 steel is a Chinese GB standard Low Alloy High Strength Structural Steel, material density is 7.85 g/cm3, tensile strength is 470-630 Mpa, and yield strength is 345 MPa. According to GB/T 1591 2008, Q345 material has 5 quality grades: Q345A, Q345B, Q345C, Q345D and Q345E.
One Pascal is a Newton (the force needed to accelerate a one kilogram object to a velocity of one meter per second) per square meter. The tensile strength of Q345B steel is rated at 470 to 630 MegaPascals (where mega is million) and a yield strength (where the material starts to thin and pull like taffy) at 345 MegaPascals.
Yield Strength; A yield strength or yield point is the material property defined as the stress at which a material begins to deform plastically. Prior to the yield point the material will deform elastically and will return to its original shape when the applied stress is removed. Yield strength of Q345B is 345 Mega Pascals.
Q345B (China, GB ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product Q345B on-line
Steel grade Q345B is the most common used as high strength low alloy structural steel in industry area.Xinsteel can offer steel coils,steel plates,angles,channels for Q345B materials.The equivalent steel grade with Q345B are EN 10025-2 S355JR,ASTM A572/A572 A572 Grade 50 and DIN 17100 St52-3.
Any request for GB/T1591 Q345B Carbon and Low-alloy High-strength Steel Plate Email: [email protected] and Tel:0086-371-65652655 Inquiry If you have any request or doubts,Please send message to us,It will be checked for you on time.
Q345 steel is an alternative to the old steel grades of 12MnV, 14MnNb, 18Nb, 16MnRE, 16Mn, etc., and it is not just a substitute for 16Mn steel. In terms of chemical composition, 16Mn and Q345 are also different.
What is the yield strength of Q345B steel plate?q345b yield Dec 31, 2018
Tensile strength of 20# steel is not less than 410, yield strength is not less than 245, and mechanical properties of A36 are about the same. Comparison of A36, SS400 and Q235 plate: As can be seen from data above, ASME standard A36 and China standard Q235 materials are named according to yield strength of material, and for SS400 is tensile q345b yield
We are GB-T1591 Q345B Steel Plate supplier . Qfsteels are specialized in exporting GB-T1591 Q345B Low alloy and high strength steel plate. GB-T1591 Q345B Steel Plate heavy plate and wide, heavy plate Which is a large steel plate supplier mill at Qfsteels Group.
Sell GB/T1591 steel coil - Q345A,Q345B,Q345C,Q345D,Q345E,Q390A,Q390B,Q390C,Q390D,Q390E,Q420A,Q420B,Q420C,Q420D,Q420E,Q460C,Q460D,Q460E with chemical and mechanical q345b yield
the yield strength of Q345B is 345MPa for thicknesses <= 16 mm. 325MPa for 16 mm < thickness <= 35 mm. 295MPa for 35 mm < thickness <= 50 mm. 275MPa for 50 mm < thickness <= 100 mm.
Q345B Alloy Structure Round Bars Stockists, Q345B High Yield Strength Shim Coils Manufacturer, Carbon Steel Q345B Plate, Coils, Angle, Bars in Shanghai, Q345B Low Alloy High Strength Unequal Leg Angle Exporters, High Strength Structural Steel Bars, Q345B Carbon Steel Plate, Q345B High Tensile Strength Steel Architectural Angles.
Q345B,Q345B PLATE,Q345B STEEL. Steel grade Q345B is the most common used as high strength low alloy structural steel in industry area.Xinsteel can offer steel coils,steel plates,angles,channels for Q345B materials.The equivalent steel grade with Q345B are EN 10025-2 S355JR,ASTM A572/A572 A572 Grade 50 and DIN 17100 St52-3.
Q235B Included in 3 standards (China) Chemical composition C < 0.22 Si < 0.35 Mn < 1.4 P < 0.045 S < 0.045 Cr < 0.3 Ni < 0.3 Cu < 0.3 N < 0.008 As < 0.08 Fe Rest It's allowed to exceed N content up to 0.014% in finished products. On exceeding N for every 0.001% max P content reduces by 0.005%. F - unkilled steel Z - killed stee TZ - special q345b yield
Haihong International Trade (HK) CO., Limited. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. Q345 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.
The min. yield point of Q235 is 235 MPa for thicknesses < 17mm, 225 MPa for 16-40mm, 215 MPa for 40-60mm, 205 MPa for 60-100mm, 195 MPa for 100-150mm, and 185 MPa for >150mm. The tensile strength is 375-500 MPa. The min. yield point of Q345 is 345 MPa for thicknesses < 17mm, 325 MPa for 16-35mm, 295 MPa for 35-50mm, and 275 MPa for 50-100mm.
Non-alloy quality structural steel Chemical composition of steel S355JR (1.0045), Standards of steel S355JR (1.0045) Mechanical Properties of steel S355JR (1.0045) Equivalent grades of steel S355JR (1.0045)
GB/T1591 Q345 includes five different steel grades as Q345A,Q345B,Q345C,Q345D and Q345E.These high tension steel grades owned the same mechincal properties,minimum yield strength at 345Mpa and tensile strength within 470-630Mpa.
Below are the tables to show the steel grade S355 datasheet including chemical composition, yield strength, tensile strength and elongation, etc. All data sheet of DIN EN 10025-2 is the same as BS EN 10025-2 and other EU member states.
Properties of Q345B Steel for Plate Material By Ken Burnside; Updated April 24, 2017 Q345B steel is a Chinese standardized low alloy, medium tensile strength steel made with a hot-rolling process, and is used for a number of manufacturing purposes. GB/T1591 Q345B Carbon and Low-alloy High-strength Steel Plate
Lastly but importantly the minimum yield of Q345 is 345MPa which is not the same as the minimum yield of grade S355 which is 355MPa. (For thicknesses less than 16mm) The members of the ASTPM would therefore like to raise its concerns to Engineers and Fabricators regarding the use of Grade Q345 in the structural market.
The standard GB/T1591 low alloy high strength steel plate of Q345 is used to manufacture factory building,drilling rig,electric shovel,powered wheel tipper,mining vehicles,excavators,loaders,bulldozers and various types of cranes.
Q235 Steel Properties and Introduction. Q235 steel is a Chinese GB standard plain carbon structural steel, and divided into 4 quality grades: Q235A, Q235B, Q235C and Q235D, material density is 7.85 g/cm3, tensile strength is from 370 to 500 MPa, and yield strength is 235 MPa (data are for steel bar or steel plate diameter 16mm).
GB-T1591 Q345B Carbon steel plate . Gangsteel sellGB-T1591 Q345B Low alloy and high strength steel plate, heavy plate and wide, heavy plate,. Q345B Adopt standard: GB-T1591 Standard Specification is for Rolled Steels for Welded Structure
Even though chemical composition is a dominant factor in determining the mechanical properties of steel, it is also very important to understand the minimum standards for the mechanical properties or performance characteristics, such as yield strength and tensile strength, which are described in more detail below. Yield Strength
Steel GradeQ235 Chemical information,Mechanical properties Physical properties, Mechanical properties, Heat treatment, and Micro structure This page is mainly introduced the Q235 Datasheet, including chemical
Q345 structural steel has good mechanical properties, low temperature performance, plasticity and good weld ability, Q345 steel is mostly used in low pressure vessel, oil tank, vehicles, cranes, mining machinery, power stations, mechanical parts, building structure, and general metal parts.
q345b yield strength
You may also leave contact information, we will contact you as soon as possible!